Central Machinery model 32208 4 speed 14" bandsaw initial impressions.

Collapse
X
Collapse
  •  

  • Central Machinery model 32208 4 speed 14" bandsaw initial impressions.

    The Central Machinery Model 32208 4 speed 14" band saw, and its single speed sibling the 32206 (only difference appears to be the pulley setup), can be an amazing band saw bargain. I purchased mine with a markdown from $329.00 to $299.00, and then used a 15% off any one item in store coupon to get the saw at $255.00 + tax. Aside from a well used saw, even 10" saws are hard to come by in that price...

    The overall fit and finish of the saw ABOVE the stand appear to be on par with the bottom end Grizzly 14", the Ridgid BS1400, and lower model Delta 14" saws. The main difference that I can see is features (2" instead of 4" DC chute, 1HP instead of 3/4HP motor, etc...). The BIG difference is where / how the motor mounts. (The CM mounts UNDER the stand, the Ridgid for example mounts behind the saw frame on the stand).

    Assembly of this saw is NOT an easy task, as the documentation is written initially by somebody that does not speak English as their native tongue, and to make things worse, they simply leave out LARGE sections of the assembly instructions. Plain and simple, have good mechanical skill going in, ask a lot of questions, and if need be, use the Harbor Freight tech support number....

    The motor bracket is shown mounted BACKWARDS in the instruction sheet. Both the printed one, and the one online. There are minimal instructions for setting up any of the safety guards, and you can only sort of hit and miss guess at where they are supposed to go... And the blade guides are a quirky design...

    As far as I know, even Powermatic band saws need some tweaking from the factory to work their best, and the Central Machinery saw is no different. It needs a much improved blade like almost every other saw on the market, as well as a decent fence, rise block kit if you are going to do any serious resawing, and at a minimum the OE blade guide blocks should be replaced with Olson Cool Blocks as soon as possible.

    The tension adjuster is a simple knob, as is the tracking adjuster.

    After the headaches and a few unneccesary cuts from the poorly finished metal edges (typical of Chinese construction) the saw is together.

    The blade appears to be tracking straight with a home brewed sled.

    As a test I cut some curve shapes out of a 3" Oak Plywood glue up / waste that was in the workshop. The saw was on the highest speed setting, and did not bat an eyelash at going through this material even with the poor quality stock blade.

    I expect many years of good service out of this saw. It is much smoother than I expected out of an HF saw, and it operates quietly.

    So far I feel this has been money well spent. Ask me in two years if I am still happy I spent the $$ on it and we will see!

    • treetopguy2028
      #50
      treetopguy2028 commented
      Editing a comment
      Check out the Iturra Design catalog for your CM bandsaw

      Iturra Design is in Jax, FL and the catalog is free. I have bought accessories and supplies from them for my Grizzly 14" Ultimate and my Hitachi CBF13. They are great to work with.
      Sherm

    • dbhost
      #51

      dbhost
      commented
      Editing a comment
      I just wanted to post a longer term update on the saw. Over the last 3 years I have hot rodded this saw quite a bit by adding a riser block, cool blocks, a Grizzly tension release, a Craftsman Fence, a link belt, and a mobile base. Overall the basic machine though, has been rock solid steady. I have last night actually, had to finally tighten up the first bolt that started loosening up on it. Like I have mentioned in other reviews of HF equipment, they tend to leave the threadlocker out of their assemblies. Not a huge deal. I added a dab of Loc Tite blue and bolted everything back down. So far so good!

    • chessnut2
      #52
      chessnut2 commented
      Editing a comment
      Hello. I just discovered this forum and it looks great. I just bought the CM 32208 and my manual says 92 1/2" for the blade. I"m hoping this is a typo. I just want to make sure this is a 32208 14" four speed that you're using a 93 1/2" on. Thanks. Jim
    Posting comments is disabled.

Latest Articles

Collapse

  • A review of the Kreg Precision Trak & Stop Kit
    by twistsol

    Summary
    I built my miter station last summer and used the Kreg Precision Trak & Stop Kit. The kit was just the starting point. 8 feet of track and a single flip stop didn’t meet my needs since I was building a miter station the width of my shop, nearly 24 feet. I added four 48” pieces of top track and three additional swing stops so I could have two left and two right. Finally, I added metric rules to the top. Total cost breakdown is as follows
    ...
    03-23-2022, 02:59 PM
  • Review of VIX-type Self Centering drill bits
    by LCHIEN
    I have always had trouble mounting small hardware on small wood boxes, with the hasps and hinges always looking slightly off perfectly square - particularly a problem with flat head screws and countersunk hardware which aligns the hardware to the hole location and centers on the hole.

    I'm talking small wood screws. I place and mark the hardware carefully and mark the center of the hole with a sharp awl.
    The problem comes about with small bits like 1/16 and 5/64 and 3/32"...
    08-30-2021, 12:18 AM
  • Grizzly Overarm Blade Guard review.
    by twistsol
    Since my new shop is in the basement, dust collection is a bit more important than when I had my own building and could do as I pleased in the shop. With that in mind, I upgraded the dust collection on my table saw. I purchased the Grizzly Overarm Blade Guard to use with the saw.

    First impressions were that this is an extremely solid and well built unit. It's made mostly of steel and connects to a 4" DC hose. There were a number of issues getting it set up and installed, and a...
    07-26-2021, 03:47 PM
  • Kreg KMA 3220 5mm Shelf Pin Jig
    by twistsol



    I decided to look for the rock bottom cheapest 32mm drilling system available that would let let me create real 5mm holes spaced 32mm apart, that was easy to use, and didn’t require a bunch of setup time. I’m really surprised at how much I like this little Keg jig especially when you consider the price of $34.99, and it has everything included. There were a couple of jigs cheaper but you needed to buy a self-centering 5mm bit to go along with them so they would...
    03-19-2021, 05:57 PM
  • Knife marking pencil Accutrax
    by LCHIEN
    Here's a tool I found useful for marking. Accutrax pencil blade marking knife.



    I have one I've been using on and off for a while. Its a fine pencil lead in the shape of a utility blade that can be installed in any utility knife handle and used with a straight edge, combination square, saddle square etc. to mark easily seen, fine lines on wood..

    Here's mine. I have not broken it, it seems to be quite sturdy. The sharp edge lasts a long time. I'm still on the...
    01-14-2021, 03:25 AM
  • Saddle squares
    by LCHIEN
    Hey, I'm sharing one of my favorite tools. A Veritas Saddle Square. Actually I have two in different sizes. This is the large size for marking 2x4 and 4x4 (shown on 4x4 here). One of those tools that makes woodworking a pleasure.



    They're great for continuing lines from side to side. And even side to opposite side.
    Works really well when the board has a rounded edge or some wane where the edge is not really sharp and square but the two adjacent faces are square to...
    01-13-2021, 02:20 AM

The SawdustZone Statistics

Collapse

Topics: 61,269   Posts: 558,427   Members: 20,614   Active Members: 74
Welcome to our newest member, Havoily.

What's Going On

Collapse

There are currently 9965 users online. 2 members and 9963 guests.

Most users ever online was 11,343 at 11:05 AM on Today.

Working...