Edge jointing large stock with a router.
Collapse
- Created by: drumpriest
- Published: 02-11-2007, 02:48 AM
- 6 comments
-
X
Collapse
-
Edge jointing large stock with a router.
There has been much discussion about how to joint with a router. The often made assumption is that one does not have a jointer, thus requires use of a router for this task. I do have a jointer, but still edge joint with a router for long boards. I find it easier to control, and sometimes quicker. Moving large or long stock over a 6" jointer isn't always an accurate process.
My method involves 4 items.
- A router - doesn't really matter what one, but runnout is a concern here.
- A flush trim router bit - a shear angle or spiral for curly stock.
- A pattern bit - for wide stock, as explained below.
- A straight edge - to guide the bearing of the above 2 bits.
My router of choice is the Bosch 1617 in the fixed base. Any router will do, one with DC is a good choice for obvious reasons. The key to this technique is having a nice straight edge to follow. I use a MDF shelf from the BORG. The reasoning is that it was cheap (5$), reliably straight (factory sliced), and 8' long. This shelf is also 1' wide.
The next step is to determine if the guide should be on the top or on the bottom. One nice aspect of using it on top is that the weight of it helps to flatten out the board if there is a little waver to it. Also you will be clamping the edge onto it, and it will act as a caul to this end. I will use the guide on the bottom when the board to be jointed is not very wide, or is of a material that will require me to use a spiral cutter.
When the MDF is on top, I use a pattern bit, which has the bearing near the shank, when on the bottom I use a flush trim bit. The first photo below is the shear angle flush trim that is used for less than straight grained materials. For seriously curly materials I use a spiral flush trim, though I avoid it if possible as those bits tend to be pricey.
As you can see in the 2nd photo, I expose as small an amount of material along one edge as possible, while having it exposed along the entire run of the straight edge. I then clamp it into place in several locations. Once done, rout between the clamps, cutting the material there straight. Then move the clamps one at a time, keeping registration to the MDF, and rout the parts missed in the first pass.
Once this is done, you can edge glue these boards together. One additional consideration is that the router bit will likely not be a perfect 90 degrees to the base. To compensate for this error, rout one board face down, then next face up, alternating as you go. This will cause this error to be mathematically eliminated.
I hope this is helpful.
Keith
Tags: NonePosting comments is disabled.
Categories
Collapse
Article Tags
Collapse
- BT3x00 (71)
- bt3000 (5)
- bt3100 (2)
- diy (2)
- dust collection (11)
- Enhancements & Modifications (5)
- Fence Attachments (12)
- General (5)
- Hand Tool Accessories (3)
- Hand Tools (14)
- Measuring & Layout (6)
- miter fence (3)
- Mobile BT3x00 (9)
- Mobile Tools (9)
- Other Reviews (4)
- Other Tools (5)
- Power Tool Accessories (28)
- Power Tools (75)
- rails (3)
- rip fence (5)
- safety (5)
- sanding block (1)
- Sharpening (4)
- t-nut (3)
- wide table kit (2)
Latest Articles
Collapse
-
by LCHIENSo you want to buy a BT3 clone. Been out of production for a while. Shopping on Craigs list or for sale ads is hard
You have to keep an eye out and you have to be used to spotting the appearance giveaway features of the various models... Ryobi BT3000, BT3100, Craftsman 22811 and 21829
There are certain things that clue you in and there are many ads that don't give model numbers and have crappy photos. Search for keywords RYOBI, Precision, System are often used in ad listings and...-
Channel: Tutorials & How To
12-20-2022, 01:53 AM -
-
by LCHIENDo you guys know your router bits?
Do you know how to tell a plunge bit from a non-plunge bit?
A non plunge bit has cutters around the periphery, but not the center. It can enter grooves from the side and cut moving sideways.
A plunge bit has cutters that go all the way to the center of the bit face. It can cut moving vertically as well as sideways.
Above see the bar across the center as well as the two edge cutters? Without this bar, when you drive the...-
Channel: Tutorials & How To
12-22-2020, 04:09 AM -
-
by twistsolI was in the shop this weekend and was trying to figure out the math for the settings on the Festool Domino to space the mortices evenly and centered across a cabinet front to back. After a bunch of trial and error with my math, I gave up and got close enough and cut the Domino slots for most of the cabinets before my shop time ran out. It was still bugging me, so I figured it out on the plane on the way to work.
Very simply, we need to subtract the width of all mortises created from...-
Channel: Tutorials & How To
01-29-2018, 12:46 AM -
-
by Sam ConderWhile attending a "fundamentals of woodworking" class taught by Marc Adams at the Indianapolis woodworking show a few years ago, I was most impressed with his simple yet effective method of sharpening woodworking chisels. I contacted Marc and asked him for permission to write an article for BT3Central on how to sharpen chisels using his method. As expected, Marc was very receptive to the idea of sharing one of his "secrets". His exact response to me was " Absolutely, please feel free to teach anything you learned from me." So let's dive right into this and sharpen some chisels.
...-
Channel: Tutorials & How To
04-29-2015, 10:15 AM -
-
by LCHIENMost common places to use air fittings in a home shop:
Air compressor to hose or female QD fitting
QD female fitting or male stud to hose
male stud to tool (such as - air nozzle, nailer, screwdriver/drill/impact driver etc, spray painter)
any semi-permanent 1/4" NPT to 1/4" NPT fitting
To add to the confusion, there's nothing on a 1/4" NPT that really measures 1/4". THe threads are visibly tapered and the overall outside size of the male NPT...-
Channel: Tutorials & How To
04-29-2015, 10:14 AM -
-
by LCHIENDigital calipers like these are available for 10-30 dollars. The size quoted as in "6-inch digital calipers" refers to the maximum measurement. The resolution and accuracy of these are typically .001 or one-thousandth of an inch. Some have an additional digit that shows 0 or 5 for half a thousandth. I recommend the six-inch Harbor freight ones, they work very well and are of surprisingly high quality. The stainless body ones are better than the composite plastic body ones although the plastic ones ...
-
Channel: Tutorials & How To
04-29-2015, 10:13 AM -
The SawdustZone Statistics
Collapse
Topics: 61,292
Posts: 558,607
Members: 20,635
Active Members: 67
Welcome to our newest member, dpkpankaj.
What's Going On
Collapse
There are currently 13428 users online. 3 members and 13425 guests.
Most users ever online was 14,350 at 01:08 PM on Yesterday.
Footer Ad
Collapse
g.
Many thanks for sharing.
Kofi